Author Topic: Inner recoil spring?  (Read 11090 times)

Offline rod m1

  • New Member
  • *
  • Posts: 34
Inner recoil spring?
« on: July 28, 2013, 07:37:04 AM »
Has anyone ordered one from Rohrbaugh or from Wolf? Yes it's a lifetime spring I believe but I still would like it replace it. They do get quit short compared to a new one.

What would a replacement recoil system cost ($40). It would be nice to have one for the range.
« Last Edit: February 18, 2015, 05:52:01 PM by rod m1 »

Offline Brenden

  • Grand Master
  • *****
  • Posts: 1747
  • Farmie!!!
Re: Inner recoil spring?
« Reply #1 on: July 27, 2014, 11:42:10 PM »
I know this is old but here is the link for springs.. Wolf
NRA Life Patron Member
GOA
Molon Labe

Offline MICHPATRIOT

  • Expert
  • ***
  • Posts: 100
  • New Member
Re: Inner recoil spring?
« Reply #2 on: March 29, 2015, 09:31:27 PM »
I just purchased recoil springs from wolf.. the set comes with one inner, one outer, and one firing pin spring.

Offline Brenden

  • Grand Master
  • *****
  • Posts: 1747
  • Farmie!!!
Re: Inner recoil spring?
« Reply #3 on: March 29, 2015, 09:54:25 PM »
I just purchased recoil springs from wolf.. the set comes with one inner, one outer, and one firing pin spring.

Excellent my fellow Michigan resident!'
NRA Life Patron Member
GOA
Molon Labe

Offline kevinqjhps

  • Grand Master
  • *****
  • Posts: 677
  • New Member
Re: Inner recoil spring?
« Reply #4 on: April 03, 2017, 07:00:15 PM »
Does the guide rod just unscrew to replace this one? Thanks


kevinqjhps
USMC
Disabled Vet
NRA
Second Amendment Foundation
FORMER Cincy Bengals fan
Three times a week shooter
Indy resident

Those who disrespect the American flag have never been handed a folded one

Offline MICHPATRIOT

  • Expert
  • ***
  • Posts: 100
  • New Member
Re: Inner recoil spring?
« Reply #5 on: April 07, 2017, 09:42:18 PM »
The end unscrews, but is has Loctite on it. Heat will be required on the end that unscrews, once disassembled, reassembly is a little tricky, I use tiny Snap-On electronics needlenose pliers to grip the inner shaft in front of the compressed inner spring to allow the cap to be screwed back on, be very careful to use pliers that do not mar the rod or the spring might drag. and with your third hand apply Loctite to the threaded end before threading the end back on. :D

Offline kevinqjhps

  • Grand Master
  • *****
  • Posts: 677
  • New Member
Re: Inner recoil spring?
« Reply #6 on: April 09, 2017, 06:56:23 AM »
The end unscrews, but is has Loctite on it. Heat will be required on the end that unscrews, once disassembled, reassembly is a little tricky, I use tiny Snap-On electronics needlenose pliers to grip the inner shaft in front of the compressed inner spring to allow the cap to be screwed back on, be very careful to use pliers that do not mar the rod or the spring might drag. and with your third hand apply Loctite to the threaded end before threading the end back on. :D




EXCELLENT. Thanks for the info.
USMC
Disabled Vet
NRA
Second Amendment Foundation
FORMER Cincy Bengals fan
Three times a week shooter
Indy resident

Those who disrespect the American flag have never been handed a folded one