The Rohrbaugh Forum

Rohrbaugh Products and Accessories => Gunsmithing or Modifications for your Rohrbaugh => Topic started by: Covert23 on December 04, 2019, 03:39:24 PM

Title: R9 parts (specifically, trigger pin)
Post by: Covert23 on December 04, 2019, 03:39:24 PM
Well, I screwed up.  After cleaning my R9, I set aside all the cleaned parts when finished.  I then decided to take the towel I was using and proceed to take it outside and give it a good shake.  Yes, I don’t have a trigger pin anymore.  Apparently I’m not very observant.  I’ve had 5 other R9’s before this one and this is the first time I realized they are two separate parts.  Every time cleaning or disassembling my past R9’s, I would just slide the trigger out and not once did they ever come apart.  I’m pretty anal about cleaning my firearms and I cannot believe I never noticed this!
    Anyway, I was hoping someone could help me out on where I could purchase this part.  I’m assuming the pin has pretty specific dimensions.  If not, is there any other firearm parts available that could substitute?  Very embarrassing. 
Thank you and I hope you all have a Merry Christmas and happy New Year! 
Jim

(Lifetime firearm owner and 25 years Retired Military.  Never in my life have I misplaced/lost a firearm or part!!!!)

Again, very embarrassing, but I’m lost without my functioning little buddy.



Title: Re: R9 parts (specifically, trigger pin)
Post by: tracker on December 04, 2019, 04:15:27 PM
Have you tried calling Alex at Williams Gunsight in Michigan? They are doing the Rohrbaugh warranty work now. The number is 800 530-9028. They have the remaining parts in stock for repairs or replacement.
https://williamsgunsight.com/gunsmithing/
Title: Re: R9 parts (specifically, trigger pin)
Post by: ECR on December 04, 2019, 07:17:40 PM
I hope Alex at Williams can help out. If not, I'll give a look through my machinist's tool box from the shop and see if I happen to have one laying around. I can't guarantee anything, but I'll give it a whirl for you.

Eric R.
Title: Re: R9 parts (specifically, trigger pin)
Post by: Covert23 on December 05, 2019, 01:53:38 PM
Thank you very much gentleman. I’ll give them a call and let ya know the outcome. Jim
Title: Re: R9 parts (specifically, trigger pin)
Post by: ECR on December 19, 2019, 07:02:07 PM
Did you ever find or get the trigger pin?

Eric R.
Title: Re: R9 parts (specifically, trigger pin)
Post by: Covert23 on February 05, 2020, 03:09:23 PM
I apologize for not responding in a timely manner.  Had to put it on the back burner Do to holidays and health issues.  Unfortunately I have not been able to track one down. Just started thinking about it again. Have a doctors apt next week and I’ve been optimistic about it and it’s got me back in better spirits.  I’m going to keep trying.  I was going to send in another pistol this spring for restoration and was going to see if he could make me one while he serviced my other project.  I’ll keep ya posted!  Thank you for checking in!
Jim
Title: Re: R9 parts (specifically, trigger pin)
Post by: ECR on February 06, 2020, 06:30:20 PM
Feel better James.

I'll look through my machinist's tool box and other areas to see if I have any of those around. At this point, some six years after the sale to Remington, parts are getting tough to find in excess anymore. I don't expect to find any, but I have found things in the past if I keep looking through the old stuff I still have here at my home. I'll let you know over the weekend sometime. I have a full plate this weekend, but I'll give it a shot for you.

Regards,

Eric R.
Title: Re: R9 parts (specifically, trigger pin)
Post by: Covert23 on February 12, 2020, 10:31:16 AM
Very kind of you sir, thank you. I’ll keep searching as well and keep you posted. Jim
Title: Re: R9 parts (specifically, trigger pin)
Post by: ECR on February 16, 2020, 11:55:39 AM
James,

I found two used barrel pins. One for you and one for me. Send me your address and I'll mail it to you.

Regards,

Eric R.
Title: Re: R9 parts (specifically, trigger pin)
Post by: ECR on February 19, 2020, 06:47:58 PM
Ah nuts. . . . . . You need a trigger pin, not the barrel pin!  Ugh...….

I'll go give a look now for those. They would be easier to possibly have around.

I'll get back to you A.S.A.P.

ecr
Title: Re: R9 parts (specifically, trigger pin)
Post by: Covert23 on February 20, 2020, 03:34:46 AM
Thank you sir.  I’m still calling around and searching and will let you know what I find.  I appreciate the help. Jim
Title: Re: R9 parts (specifically, trigger pin)
Post by: ECR on February 22, 2020, 05:42:07 PM
Good Evening Jim,

Okay, we're in luck! I found a few trigger/sear pins. These measure .125" x .725".

If you pm me your mailing address, I'll get one of these in the mail for you no charge.

Talk to you soon.

Regards,

Eric R.
Title: Re: R9 parts (specifically, trigger pin)
Post by: Covert23 on February 24, 2020, 01:14:47 PM
Sir, I sent PM yesterday but it did not show up in my sent messages.  I just another so hopefully you will receive this one.  Please let me know if it doesn’t get through. I appreciate your time and help!  Jim
Title: Re: R9 parts (specifically, trigger pin)
Post by: ECR on February 24, 2020, 06:53:45 PM
Just got back home from helping a friend in need in upstate New York. I sent you a PM here.

Get back to me when you get it via PM also.

I do have a trigger pin for you!

Regards,

Eric R.